What Is The Medication Quanapin Used For

The situation in

Hi all, bloggers z'amis z'et readers (bloggers z'amies z'et readers also obviously) (... especially well ^ ^)
Since the last post, there is no stubble. As we are motivated, we take advantage of: the doubling of the living room wall (the side pantry) is completed, Estelle began to build on the elec and we have a multitude of sockets and switches that work. There's even lights that light that we should proceed without the strip. The large class what! Listed
plasterboard joints, the 1st pass (+ tape) is made almost everywhere, is more than the 2 mega-horizontal stripes on the 1st floor, my electric plane having died during I was digging the groove ... It was not made for? really?
Besides if someone has a good tip before it is the grinder that ramassse, I'ma taker ...
Here for the latest news is not bad.

As this month it's been 3 years since the adventure began, I wanted to do a big post a point on the progress of work (or non-advanced, it depends).

Remember, at first, after 2-3 sledgehammer, it was like this:

one of my favorite pictures of the yard!

Ground floor lounge: was poured screed, lined and insulated 3 of 4 walls, electrified all (for walls clad ...), extended the chimney and installed a wood stove.
That leaves a wall plate, a small cupboard to wall-off the entrance to the tile in place, strip and stain the door to the garden and put a staircase to the first.

much better that before

ground floor kitchen-room-WC: cooking studio has served as a first step. It is in ruins, must redo everything, there's leaks, no elec and is below the ceiling so the barn is blown to pieces as soon as we attack this part of the house. Will redo the drainage of water, a fork-patching, put the tile and implement a kitchen and toilet, shower mount a floor ...

no photos for now

ground floor storeroom: insulated ceiling, elec OK but walls and floor in the state to disburse land ... one day ...

the photo, the ceiling is not insulated

ground floor garage in the state, maybe one day my studio? currently full bazarre, pavers, furniture, old doors and windows, props builder, former boiler + tank ... Brief inaccessible when something is in the garage, we do not ...

no photos for now

ground floor garden nothing is done, it maintains the best least evil that can and do faudrat 2-3 small earthworks, driveways for move and certainly massive and ptits green stuff to put on the right and left. And then a little light too might as well.

... we will wait until it melts;)

1st floor guest room: was all redone from floor to ceiling, the room is complete (except the bars of the window and the niche that has received this week and are currently under glaze) and is currently our bedroom.

the picture a bit dated, since y 'curtains, carpets and gadgets to decorate ... see Miss for more info:)



1st +2 nd floor plate floor mezzanine : Ground OK (chestnut beams, joists and flooring), 3 of 4 walls of plywood (the 4th is on hold, we expect the builder to make an opening toward the barn), electricity OK on the 3 walls, insulation and ceiling panels OK too:)
remains a wall plate, the opening to the barn to putting the stairs to the mezzanine, put the toilet underneath the floor sanding and vitrify

first floor barn yard not started, will redo the floors, double walls, insulation and wainscot (?) the ceiling, creating a bathroom, bedroom, and if possible a mini loft above the bathroom to tidy the mess ... Briefly, to

no photos for now

2nd floor attic: we redid the floor (beams, joists and CTBH), isolated and plated ceiling, lined the walls ... Briefly, this is the second part really finished with the guest room.

completed ... for an attic, if it should become a bedroom, will still put a laminate floor finishes and refine ...

Here for the inventory, good in three years, there's been a hard fact but it was still not trampled. As against this is still not sick of living in the dust Permanent or having them put the weekend, it has not made great sores (as long as it lasts), so far, so good, better and even better! :)

Oh yes, we should also redo the facade in a few months and the door is almost ordered, but that's the one we will po ^ ^

... In any case it is not about closing the blog: D

Does Biting Nails Stunt Finger Growth?

speed ...

A 'tite quick photo with the phone (we loaned AFN to cover a happy event , Enzo welcome:) ). The wall above the staircase is the first ROC-plated Finally, everything went well (no hyper snug but hey, you chew). Next step, a wall in the lounge and double ... 3km to seal ..... : /

Seen from here ( ROC), that's pretty damn high, not ? J
'get enough of this view:)

How Long Does It Take At The Meps

Comeback

Whaa dust here is worse than ours!

Well, after all this time, you've all seen that we had a beautiful stained glass? It is one
Finally some ptits stuff to tell:) Nothing to marvel
not eh, it just gives them.
We confess, in 7 months was not fucking with nothing fucked up, but then nothing (well at work because, otherwise, it was full of cool stuff but do not advance the Schmilblick).
So I said, it was quietly taken the last weekend, with the program:

-Estelle, installation of new outlets which operate on the entire plateau (yes!!) And the perennial sanding of the beam above the mezzanine (with harness and climbing cow, it's safer)
-for me, a lil shot mechanic with the rails of the future septum above the ground floor staircase-1 (with nothing in a vacuum, on tiptoe at the top of the scale, it is less conservative) and the end of the hopper of the mezzanine.

For once, it went well, the beam starts to look good and the wall is straight (better!) and ready to be isolated. It was reasoned that because once finished wall (...) we will finally put a staircase! Because there ... fed scales dangerous at night ...

Those are all small news, normally we're back and we'll have more stuff soon to tell :) PS

: THANKS TO ALL AND ALL for your mail and your coms (and even anonymous impatient eh Siya!;)) That made us really happy to see that even when we say nothing you still go for news, so thank you again the z'amis miles:)))

Gemmy Holiday Light Show Tree Not Working

Vitrail: 8th episode - End of 1st season

Today ... end of the window!

First, smoothing the overlap areas: using a mini-spatula to fully retract the seals and crush one just above. After using a kind of plastic spoon to fold the wing of lead glass. The gesture must be flexible and smoothly. We finished preparing the pellets by brushing for thorough cleaning (dust lead glop = no: (next time I'll put a mask).

Then we prepare the welds. We put the brush "fat degreaser" (yes, I swear, it works, but I have not understood the trick ...) taking care of the well to penetrate between the wings that overlap. It's funny, fat dry cleaner in the lead ( grease dries?! really not understood the trick ...). Then Yapluka welding rods with large tin. I even states that where there was no aa fat, tin HOOK not. I'm not super-proud of my welds ... but hey it is not clear. Not hot enough it sticks the wand, it burns too hot lead, tin is not quite fragile, it is too big pate, patouille is dull and brittle ... Brief must be right first time!

Finally, the last weld. Now go back the window, but then very gently. And this post is taken from the beginning ... (Unless you've already read this sentence) And oh

victory was over! ... Well almost ...

just returned, Yann has been searched the small window. And second victory in the window returns the site! 1 mm less in width and 5 mm in height. As a black tape on the edges of the glass to have no light passing around the edges.
For fixing, we opted for making small spikes on the edges of the window, folded around the edge of the window. It is.
We raced the sun to see what it looked like ... but it was he who won


Click on the images! (The blue sky is an effect of the glass is white!)

PS: for orders, no delivery expected before 2012, given the number of things I already do to;)

Re PS: Thanks for all your comments, it's nice ...

Can Foot Drop Cause Edema

Vitrail - Episode 7

's it's over!
No, actually it's not true ... During more than I promise you my love! I've already talked about the next windows? ... Oops j'vous tell you later. And as

are 2 lame bored to their PC or Mac;) I will detail all you!

The implementation lead is complete. I find it much harder than the cutting of glass. We must measure properly prepare the pellets, which must be open and crush them to other places (but not too much because the glass must still return it). We must be careful tracking, and order of laying bits of glass to keep the stained glass. It must be said that if not maintained ... while on the lam (hence the small nails to hold the As). In short, not easy.

All this to realize that my last piece did not fit into the slot, then forced to "relax" the window (with the risk that a glass so the "throat" of lead or a lead sort of another in which it was made), to slide my last end. After
is closed with two strips of lead and fixed a clipboard to hold the assembly. Then taking measurements, 32.3 on one side, 32.5 on the other ... not good, then we unpins the board and he tapped with a mallet (not afraid) to "settle" the window.
When it's good, we nailed the board, it will move over to the welds.

Next week, beating and smoothing weights, then fitting the oil degreaser (not including the shot of the fat that removes grease), and welding this side. Then turning over (will have to be careful) and welding the other side. And finally fitting and admirage!

Ds Emulator Mac Pokemon Diamond

Before the sky falling on our head ...

I already mentioned, the firm is caught in a piece of wall instead not super strong ...
Let's say the elders (who knew what they were doing it for fame) have managed to get the chimney flue almost directly below that big beam that was happening already flush with the ridge of the barn! ! Result, it wanted much more on and it worked ... not top ...
Prior to taking the roof over his head, was cast a concrete base + scrap between the joists of the first floor. Then we put 2 posts (50mmx220mm), one on each side of the wall, connected by threaded rods to strengthen the whole. they disappear later in the dubbing. Not even afraid to poke holes in something already fragile ...
Normally this beam should not move, we hope. There's other stuff in the same style barn side, will deal with it first before attacking anything in this second part of the house ...
the left side view platform, and right next to barn, where we see a small leak in one of the joints of the chimney, one more line on the Todo list ...
Ok, 2 poles and 5 holes, it's not a full weekend, but I managed to badly twist my ankle (as that is the most stupid, go ...) So today, forced glandouille and TFW transition to hosto if it will be better. A week before the holidays when we had (finally) a little skiing ... Really great ...

Curious About What Women Wear

Vitrail - 6th during

Today "plumb" it does not "seal" is checked;)
Well I reckon it's more subtle than I thought. I finally finished it today at all ... Perhaps the next meeting?

To begin we must nail two boards on a wooden work (ultimately it is not quite my board?;)). They are profiled in> an edge to avoid damaging the lead that comes cons. These 2 boards provide the right angle of the window. Then
we put a strip of lead on each stick (size of the window + 2-3 cm). And we can begin to assemble and lead glass. One attack angle. We must reflect on the path of the lead strips. After 3 pieces of glass that gives it:

As the glass cup in the "low" lead, we must put a nail into each piece ... nail being removed as we go into the next room ... AC serves to keep the window up ... Not even afraid to drive nails cons pieces of glass:))

tools is simple, a lead strip profile H. It is sold in flat roll a few times (he must be careful well unroll flat spin and if it is bloody). A piece of string to measure and report the size of the lead tape to prepare.
After the thing must be blue in the picture (a spacer?) To fully implement the right lead, the 2 sides. As is soft, it deteriorates quickly ... and glass should go in without problem.
We use the knife to cut the lead, but also to open it there or there are crossings. As a lead goes in the other, it takes a little crush the first with the flat of the knife, and it takes a little away by the second lever. It still uses the knife to cut pieces of lead that exceed once they are caught between 2 glasses.
At the end of the session I was there:


By cons must wash their hands after (the lead is not good for health). Maybe I'll put the gloves next time.

A Sunday ... for new adventures! (And hopefully a little soldering)

What Kind Of Mucus You Get Before Your Period Due

insulation pantry

Just wanted to say that finally we could not bring himself to put on our beautiful hardboard beams. We just put a tarp in the meantime and when it will be a true cellar-flat-en-hard (for now, is earth ground, there's 20cm of false level ...), will be the wainscoting or batten ceiling.
Tarping Before, I brushed my beams with concentrated bleach to remove a fungus blue / black began to spread, it works great!
For glass wool, as I had not solved my problem of vapor barrier, bah, I'm not dressed! And more as the sheet is transparent, I would see quickly if there is or not condensation. So I asked the bare glass wool 10cm thick roll, I cut the strips with a cutter and saw before undoing the roll, it goes really fast and it puts in less everywhere; )

PS: it was good to isolate!

... a lil picture of the garden for D & O;)

I think that Estelle will soon make a post to the window ... I saw the pictures, it's still not finished, but it's nice:))

What Does Strep Throuat Look Like

Stained Glass - Season 5 Maid

Today we'll look to No. 28:

Cutting is drawn on the glass with the label (we put the cardboard template on the glass and follows the contour of the felt).

is arming the diamond and is blackmailed the glass on the inside edges of the green line! Then they break. 2 cuts for the top photo. For small pieces (like the thin edge), take the pliers to break the glass (not making enough to break it with your fingers or the edge of the table). That gives it :

And then you tell me .. There is a crater! ;) Small spikes can not remain in excess, they interfere lead. It should be ground.

That done, place the tip cut back its size and it only remains to check the light nothing more than ... Otherwise, green marker there or exceed it, and re-grinder until ...

The tip over, it remains only to make him join his fellows!
That's it, all the pieces of glass are ready:

Next meeting: assembly lead ... (Filling? I'll find out)
A priori it should even take me 2 sessions, we'll see ...

Things To Write To Someone Who Just Had Baby

question ...

During that Estelle ended the cutouts of the window, I finally finished the pantry store.

Well yes, it was not finished last!

And when I say "vacuum" ...

few ... no trips to the recycling center!

The purpose of this storage is to move to insulate the ceiling of the cellar, because as above, it is our room and the pantry is as handy as a piece called "cool" as the room would be nicer with a floor a bit warmer;)
We'll put some glass wool between the joists and make a false ceiling hardboard. I can hear "Arrggghhh! His French ceiling! the ugly white hardboard! sacrilege! " ... and you're right. But hey, it's a cellar and I have neither the desire nor the time to flatten the joist (or make a lime-coated flax;)) So, it will be content ... but it will be ugly ...

To return to the post title, I have a question you submit for insulation, air barrier steam I put down hardboard side or top side of the room floor?
I tend to say it up but I still have a small doubt ... If anyone can enlighten me. ..

Jaw Pain When I Drink Alcohol?

is at it again ....

Some time ago we made family visit Siyadurocksava ... bin and now it is them who came! And since it is they who are the road, first post!! ;)
must hurry ...

You think they'll find? You're on your plan? That's all stored? You've finished passing the suction? How it is hanging by a thread?

bin And we still had a great afternoon with them! Tower owner (forced between renovators!), Gossip, food, small talk, little walk, chatter, and we even made our work neuron with games including a Scooby-Doo rules incomprehensible ... We find that one is speed and really anyone can play (children and adults) is cool.

blogger and his best friend (the one we never see): the digital!

How it is late! But they have just arrived (

Siya you soon, thank you again for your visit, it was great!

See you soon ... for your first rack as soon as the bathroom, and the corridor walls, and floor of the corridor will be made ... Siya, do not hang out ... at work!;)

Epson Scanner Kodachrome

5 minutes respite for the planet ... Stained

February 1, 2007, in all France: Join the largest mobilization Citizens against Climate Change!

The Alliance for the Planet launches a simple call to all citizens, 5 minutes respite for the planet : Everyone should turn off his lights and watches the 1 February 2007 between 19h55 and 8:00 p.m. . It does not save electricity only 5 minutes that day, but to draw attention citizens, media and politicians about the waste of energy and urgency of taking action! 5 minutes respite for the planet : it does not take long, it costs nothing, but shows the Presidential candidates that climate change is a subject that must weigh in the political debate.

Why February 1? Because the next day out in Paris, the new report from the Intergovernmental Panel on Climate Change (IPCC) United Nations. This event will take place in France: do not miss this opportunity to shine spotlight on the urgency of the global climate situation.

If we all participate, this action will have a real media and political weight, less than three months before the presidential election!

For those who are not convinced ... find a way to watch this story: An Inconvenient Truth . It's a bit of a film campaign for Al Gore, but it sums up the situation.

It's worth it, right?

Impacted Bowels Treatmemt

: 4th episode

No damn much ... I wanted to finish all my cuts and bin no, I made it myself and 7 remaining 10 ... But I made the oval was cut the most complicated. It should "fit" by an edge of glass, join the line of the oval, so we can follow, and "out" of glass on one edge. Then you must "break" the piece cut without damaging the oval. And again ... For the oval, at least 8 slices. There if you follow ... you tell me ... remains peaks glass ... and yes, so we start by grinoter with pliers (it's been super scared ...) and a tuning with the grinder.

I love this glass, it changes color and transparency. (This is the same oval on the picture below, as what Having a glass with a transparent background and it does not like)

So I finished my next course cuts and the one after I mount the window with lead, soda, and I ... But if my love more than 2 and it's good ... must say that I have exhausted my credit gift so now we pay our way;).

Besides it's worth it to take courses, 15 € 2 hours, the equipment is provided (tools, glassware, lead, coffee, etc. ...). You should know that the glass plates are very expensive (50 to 300 € / m2 depending on the types and colors). So when you need just a little bit of color it is an expensive little piece!
hardware from top to bottom: the diamond wheel to kind of "singing" scratching the glass, it's where it should break. Then the clamp snack, go ahead, imagine nibbling the edges of a piece of glass that you do not break;). And then comes the marker to trace the contours of the cardboard template on the glass ... So we cut on the inside line of the label;)

Anyway, to this day I'm here:


the way my love ... I go back Sunday!